El number is a product/article number used in Norway.
This large capacity unit can control up to 64 wireless devices.
Otherwise same functionality as GSMECOComfort but with Modbus and RS485 in addition and intended for installation in the fuse box.
See GSMECOComfort for more details.
ECOGlamoxPlug is connected directly to the heater and provides the option to centrally and remotely control heaters via our apps.
You decide the energy saving and the comfort temperature for the heater. Minimum energy saving temperature is 5 degrees Celsius and maximum comfort temperature is 40 degrees Celsius.
Our apps make it easy to switch between energy saving and comfort temperature or to set up a Minuterie hebdomadaire.
ECOGlamoxPlug transmits the temperature measured on the back of the heater so that you can see the temperature in our app.
ECOGlamoxPlug makes it easier than ever to control heaters from your mobile phone.
Compatible with Glamox heaters of type 3001.
ECOBEHAPlug is particularly suitable for a house or cottage where you want to be able to turn the heater off completely when you are not there (energy saving function "OFF").
ECOBEHAPlug is connected directly to the heater and gives you the option to control the heater centrally or remotely between either:
1) Comfort temperature, the temperature is set on the thermostat wheel on the heater
2) Energy saving function. There are three energy saving settings: night temperature, frost function or off (heather completely turned off).
The default setting is night temperature. You can choose energy saving setting in the app.
Explanation of the three energy saving features:
Night temperature - the temperature is lowered 4-5 below the temperature that the thermostat wheel on the heater is set to.
Frost function - the temperature is lowered to around 5-7 degrees.
Off - the heater is turned off completely and will not turn on until the systemet is set to comfort temperature again.
The temperature in the room is not accesible via ECOBEHAPlug. For temperature reading, we recommend a product such as ECOTemperatureSensor10K47K or WirelessTemperatureDetector.
All control is based on the temperature wheel on the heater. ECOBEHAPlug is compatible with all BEHA heaters of type P and L produced from August 2005.
Bruker firkantet boks til CTM Lyng, festes til vegg (altså ikke skjult installasjon).
Foreslås av Terje at ventes med siden liten etterspørsel. Kan kanskje bestille 100 stk siden lite marked foreløpig.
Er altså ferdig for produksjon.
ECORelay has 3 16 A / 3600 W potential free relays with associated port for cabled temperature sensors.
The relays can be used individually as on/off switches or thermostat. By connecting cabled temperature sensors it is possible to make a temperature reading and activate temperature monitoring to send alerts at low temperature.
You can also activate thermostat function individually on the relay with a connected temperature sensor and use them as thermostats - switch between energy saving and comfort temperature.
ECORelay also has 3 ports for cabled alarm equipment, plus a siren relay which is activated if the central unit is activated by fire or break-in.
The relay module communicates wirelessly with the central unit, so it is very easy to install.
ECORelay also has control buttons so that you can control each relay locally.
Runs either on mains electricity or 9V battery.
The smoke detector will of course have a local alarm as well as sending a warning to you.
If one detector is set off all other detectors will also be activated.
The main advantage with a cabled temperature sensor is that it never runs out of power. ECOTemperatureSensor10K47K is equally suitable for open and hidden electrical installations. It can be installed straight onto the wall or directly on a wall box for a hidded installation.
ECOTemperatureSensor10K47K has two temperature sensors of NTC type, one at 10 kilo ohm and one at 47 kilo ohm so that it is compatible with both old and new equipment.
ECOTemperatureSensor10K47K has a classic sleek design (RS16).