Protocole radio 2 de Sikom (récent)
Please note that a lot of new auxiliary equipment supports both old and new Sikom radio protocol(Protocole radio 1 de Sikom (ancien) and Protocole radio 2 de Sikom (récent))
However, newer central units such as GSM ECO-Comfort and GSM EcoStarter Touch do not support old auxiliary equipment.
This large capacity unit can control up to 64 wireless devices.
Otherwise same functionality as GSM ECO-Comfort but with Modbus and RS485 in addition and intended for installation in the fuse box.
See GSM ECO-Comfort for more details.
ECOGlamoxPlug is connected directly to the heater and provides the option to centrally and remotely control heaters via our apps.
You decide the energy saving and the comfort temperature for the heater. Minimum energy saving temperature is 5 degrees Celsius and maximum comfort temperature is 40 degrees Celsius.
Our apps make it easy to switch between energy saving and comfort temperature or to set up a Minuterie hebdomadaire.
ECOGlamoxPlug transmits the temperature measured on the back of the heater so that you can see the temperature in our app.
ECOGlamoxPlug makes it easier than ever to control heaters from your mobile phone.
Compatible with Glamox heaters of type 3001.
ECOBEHAPlug is particularly suitable for a house or cottage where you want to be able to turn the heater off completely when you are not there (energy saving function "OFF").
ECOBEHAPlug is connected directly to the heater and gives you the option to control the heater centrally or remotely between either:
1) Comfort temperature, the temperature is set on the thermostat wheel on the heater
2) Energy saving function. There are three energy saving settings: night temperature, frost function or off (heather completely turned off).
The default setting is night temperature. You can choose energy saving setting in the app.
Explanation of the three energy saving features:
Night temperature - the temperature is lowered 4-5 below the temperature that the thermostat wheel on the heater is set to.
Frost function - the temperature is lowered to around 5-7 degrees.
Off - the heater is turned off completely and will not turn on until the systemet is set to comfort temperature again.
The temperature in the room is not accesible via ECOBEHAPlug. For temperature reading, we recommend a product such as ECOTemperatureSensor10K47K or Sonde de température (sans fil).
All control is based on the temperature wheel on the heater. ECOBEHAPlug is compatible with all BEHA heaters of type P and L produced from August 2005.
ECONodeWallSocket makes a neat and permanent installation easier without the use of wireless plugs such as ECO Node (el.nr: 64 311 24). The installation is simply much safer.
ECONodeWallSocket is equally suitable for open and hidded installations. Max load 16A/3600W. Everything that is connected to ECONodeWallSocket will be remote controlled so it is important not to connect electronic devices that you don't want to control remotely.
ECONodeWallSocket can be used as a switch (on/off) or as a thermostat (energy saving/comfort).
To use ECONodeWallSocket as a thermostat it needs to be connected to a temperature sensor. It is then possible to set an energy saving and a comfort temperature that you can switch between. It couldn't be easier.
ECONodeWallSocket needs to be registered in the central unit through a specific process described in the user manual.
ECORelay has 3 16 A / 3600 W potential free relays with associated port for cabled temperature sensors.
The relays can be used individually as on/off switches or thermostat. By connecting cabled temperature sensors it is possible to make a temperature reading and activate temperature monitoring to send alerts at low temperature.
You can also activate thermostat function individually on the relay with a connected temperature sensor and use them as thermostats - switch between energy saving and comfort temperature.
ECORelay also has 3 ports for cabled alarm equipment, plus a siren relay which is activated if the central unit is activated by fire or break-in.
The relay module communicates wirelessly with the central unit, so it is very easy to install.
ECORelay also has control buttons so that you can control each relay locally.
It is designed for hidden installation and delivers two control signals to the thermostat: 230 VAC and 230 VAC via a rectifier diode. This makes the thermostat completely flexible.
ECOThermostatPlug has been tested with:
Comforttemp 750 from VarmeComfort - Day (comfort), Night (energy saving) or frost protection.
Comforttemp 740 from VarmeComfort - Day (comfort), Night (energy saving) or Frost protection.
Multireg LCD2 from ThermoFloor - Day (comfort), Night (energy saving)
MTC2-1991-MH from MicroMatic - Day (comfort, Night (energy saving) or frost protection.
ECOThermostatPlug communicates wirelessly with the central unit so it is very easy to install. We recommend a wall box with a depth of 57 mm together with ECOThermostatPlug.
The thermostat can be remote controlled, with the option to change between normal, night mode and frost protection.
Please note that our thermostat products, such as ECO Thermostat SI-3 10Aand ECO Thermostat SI-3 16A has inbuilt remote control.
Runs either on mains electricity or 9V battery.
The smoke detector will of course have a local alarm as well as sending a warning to you.
If one detector is set off all other detectors will also be activated.